Pool Equipment Installation in Guadalupe

New Equipment That Fits Your Pool

Your equipment pad does the quiet work that keeps the water clear: the pump moves it, the filter catches what floats in, and a heater or salt cell handles the rest. When one of those parts is failing, a repair is not always the best value. We give you an honest answer on whether to fix it or replace it, and if replacement makes sense, we install the new unit properly.

Most of our installs are pumps and filters, followed by heaters, heat pumps, salt chlorine generators and booster pumps for pressure-side cleaners. We match the equipment to your pool's volume and plumbing, so a new pump is not oversized and fighting a small filter.

We also work like guests at your home. Drop cloths go down, cut pipe goes in a bucket, and the pad is swept before we leave.

What an Installation Includes

Sizing before we order

We look at your pool's gallons, pipe size and existing filter before choosing a pump or heater. Correct sizing keeps flow steady and avoids wasted power.

Removal of the old unit

We disconnect and take away the old pump, filter tank or heater. You are not left with a heavy motor sitting by the trash cans.

Clean plumbing work

New unions, glued joints and valves are set square and supported. Neat plumbing is easier to service later and less likely to drip.

Electrical hookup to the existing circuit

We connect the new equipment to the circuit already serving your pad and check the bonding wire is attached. If we find wiring that needs an electrician, we tell you before going further.

Startup and settings

We prime the system, check pressure and set run times or speeds. For variable-speed pumps, we program schedules that suit your pool and the season.

Tidy finish

Boxes, foam, pipe offcuts and old fittings leave with us. We rinse any PVC dust off the deck and sweep the pad.

Signs It May Be Time for New Equipment

• A pump that screams or hums

  Grinding or a loud whine usually means worn motor bearings. A hum with no spin often points to a failed capacitor or a seized motor.

• Repairs piling up

  If the same unit has needed parts two or three times in a short stretch, replacing it often costs less over time than another repair.

• Cloudy water despite good chemistry

  A cracked filter grid, a worn cartridge housing or a pump that no longer moves enough water can leave the pool hazy even when the balance is right.

• Leaks or cracks at the pad

  Water pooling under a pump, or a cracked filter tank, means a part has reached the end. Long summers of sun and heat make plastic housings brittle.

• High power bills from an old single-speed pump

  Older single-speed pumps run at full power every hour they are on. A variable-speed model can run slower for most of the day and still keep the water moving.

How Install Day Goes

1. 1

   Phone call and look at the pad

   You tell us what is happening, and we set a time to see the equipment. We explain what we found and give you a written quote before anything is ordered.

2. 2

   Protecting the area

   On install day we lay down mats where we work and carry equipment along a clear path. Gates get closed behind us so pets stay where they belong.

3. 3

   Swap and plumb

   We shut off power, remove the old unit and fit the new one. Joints are glued and given time to cure before water runs through them.

4. 4

   Startup with you

   We start the system, check for leaks and walk you through the controls. You know how to switch modes and what normal pressure looks like.

5. 5

   Cleanup before we go

   Old equipment and all packaging go in our truck. We sweep the pad, rinse the deck and leave your yard looking the way we found it.

What Affects the Price

Every install is quoted after we see your pad, because the equipment and the plumbing around it differ from pool to pool. Your quote lists the equipment and the labor separately, so you can see where the money goes. If something unexpected turns up, we stop and talk with you before doing extra work.

Type of equipment

A variable-speed pump, a heat pump and a cartridge filter all carry different costs. We can show you a couple of options at different levels.

Pool size and plumbing

Larger pools need bigger equipment. Pipe size and how far the pad sits from the pool also change what fits.

Changes at the pad

Moving a unit, adding valves or replumbing a crowded pad takes more time than a straight swap in the same spot.

Electrical or gas work

Some upgrades need a new breaker, a dedicated circuit or a gas line for a heater. When that work is needed, we explain it up front so it is not a surprise.